driven machine
英 [ˈdrɪvn məˈʃiːn]
美 [ˈdrɪvn məˈʃiːn]
网络 从动机
双语例句
- It is driven from a different machine.
它可以从不同的机器上驱动。 - Model Parameter Identification and Sliding Mode Control of Automobile Clutch Driven Disk Test Machine
离合器从动盘测试机模型参数辨识与滑模控制 - Repulsion start induction motor Design of snubber circuit's parameters in thyristor driven induction machine system based on steady state optimization
推斥启动式感应电动机基于静态优化的晶闸管驱动感应电机系统缓冲电路参数设计 - Units of this type must be connected with the driver and driven machine using flexible couplings.
此型号其二端必须以可挠曲性连轴器联结动力源与被驱动元件。 - Custom Requirement Driven Forging Machine Rapid Design System Based on Pro/ E
基于Pro/E的客户需求驱动锻压机床产品设计系统研究 - Diesel engine driven DC arc welding machine
柴油机驱动直流弧焊机 - The main bearing and each dial are driven by electromotor of main machine through reducer, and numbers of roller which are rolling in the ring, which are driven by dial through plunger.
主机电动机通过减速器带动主轴及各层转盘旋转，转盘通过柱销带动几十个环辊在磨环滚道内滚动并旋转。 - Compressed-air driven roller covering machine
压缩空气驱动的套皮辊机 - Compressed-air driven waste processing machine
压缩空气驱动的废物处理机 - Model MN: This is a general hand driven flat knitting machine, which can make single-sided and double-sided fabrics with jacquard.
MN型：普通平机，可生产各种花式的单双面织物，无提花设计； - Aolung Electric Machine Development Co., Ltd is the first manufacturer that in line of green energy resources micropower driven machine and generator in Macau.
澳能电机发展有限公司是澳门首家专业从事绿色能源微型电机及发电机产品的制造商。 - As the core component in layer K, the UMS mail server is responsible for the storage, transmission and management of the system driven by the layer-K state machine.
UMS邮件服务器是系统三层体系结构中K层的核心模块，在K层协议机驱动下完成存储、转发及管理等任务。 - Technic of Import Shield Driven Machine
盾构掘进机引进技术 - Performance of gas engine driven compression-type refrigerating machine
燃气机驱动的压缩式制冷机组的运行特性研究 - A New Type Electro-Spindle Driven Testing Machine for Double-Ring Rotating Bearings
电主轴驱动双套圈旋转轴承试验机 - Calculation of Motor Driven Power of Coiling Plate Machine
卷板机电机驱动功率的计算 - Analysis of Load and Design of Driven System for Bundling Machine
打捆机驱动系统的设计和受力分析 - This paper introduces an automatic paper stand of which the scaleplate is driven by the micro machine controlled by closed cycle circuit. The paper stand is of low cost. Its accumulated error is less than 0.8 mm every 30 lines.
本文提出一种采用闭环控制电路，控制微电机带动标尺的稿架方案.该稿架具有成本低、30行的积累误差小于0.8mm； - Finally, this method was applied to the design process of the new-type self-driven towing machine.
最后应用于新型自驱动式牵引机的协同设计过程。 - Comparing this new model machine with its traditional form, the LIM driven punching machine has many advantages, such as, simple construction, small size and weight, low production cost, short production time, easy to control, low noise and considerable energy saving.
和传统式机械冲压机相比，直线电机驱动的冲压机（以下简称电磁冲压机）具有结构简单、体积小、重量轻、制造周期短、成本低、控制方便、噪音低和省能等优点。 - These types of fluid couplings, installed between a constant speed motor and driven machine, can provide stepless output speed regulation, and reduce electric power consumption. Machine Tool Driven by Center of Gravity
介绍了液力偶合器是在电机转速不变的情况下实现输出转速的无级调节的，从而提高电机的起动能力、减少冲击和振动，协调多机驱动的负荷分配 - A new hydraulic driven system in the machine for pipe end bevel
管道坡口成形机的新型液压驱动系统 - Mechanical engineering and maintenance considerations of a felt roll driven paper machine dryer section
纸机干毯辊传动设计与维修 - Motion controller is the equipment that control the motor driven machine to implement the expectant motion locus.
运动控制器是通过对由电机驱动的执行机构等设备进行运动控制，以实现预定运动轨迹目标的装置。 - Taking simple ball-cone workspace as an example, the relation among the fixed platform radius, mobile platform radius and the length of driven bar of 6-SPS parallel machine tool is discussed. Some conclusions for designing the construction dimension of 6-SPS parallel machine tool are presented.
以简化的球锥体工作空间为例，研究了六杆并联机床固定平台半径、运动平台半径、驱动杆杆长三者之间的关系，得出并联六杆机床结构尺寸设计的一些结论。 - Summary of cutter head of shield-driven machine
盾构刀盘设计综述 - Research and Development of Control System of Continuous Driven Friction Welding Machine
连续驱动摩擦焊机控制系统的研究与开发 - Analysis for Producing Cold Rolling Ribbed Wires and Bars Driven by Drawing Machine With Double Drums
双层卷筒拉丝机拖动生产冷轧带肋钢筋分析 - Pointed out that the all-electric servo-motor driven injection molding machine is not suitable for our country at this stage because of the high cost and we should develop the hybrid electro-hydraulic injection molding machine. 2 Two electric-hydraulic driven hydraulic system solutions of the injection molding machine are proposed.
指出了采用全伺服电机驱动的纯电动注塑机由于成本较高不适合我国现阶段的发展而应以发展电液复合式的注塑机为主，并提出了本文研究的主要内容。 - First, paper introduce the driven machine of linear motor hoisting system, the basic structure, classification, working principle, characteristics, etc. Then talk about the structure of hoisting system, work flow analysis.
首先从直线电机提升系统所采用的驱动电机&永磁直线同步电动机的基本结构、分类、工作原理及特点等方面进行介绍，进而对提升系统的结构、工作流程进行分析。